Feedstock Hopper: Printing and assembly
The shipping configuration: 202 x 202, two segments, regrind at 70 degrees,
mounted on the MK3S frame. just render writes every part.
| Part | Qty | Size (mm) | PETG | Orientation |
|---|---|---|---|---|
| body segment 0 | 1 | 173 x 173 x 205 | ~0.37 kg | flip – flange down |
| body segment 1 | 1 | 202 x 202 x 205 | ~0.66 kg | as modelled |
| cap | 1 | 209 x 209 x 19 | ~0.22 kg | flip – top face down |
| hub | 1 | 95 x 95 x 36 | ~0.08 kg | as modelled |
| plate (MK3S) | 1 | 135 x 135 x 98 | ~0.46 kg | flip – plate face down |
| outlet | 1 | 59 x 61 x 83 | ~0.06 kg | as modelled |
About 1.8 kg of PETG all told. Masses are the solid model volume at 1.27 g/cm3; infill below 100% brings them down. Segment 1 at 202 x 202 leaves 4 mm either side on an MK3S bed, and the cap at 209 leaves half a millimetre – check first layer placement rather than trusting it.
Why those orientations
Section titled “Why those orientations”Downward-facing flat area above the bed, per part:
- Segment 0 has 8 280 mm2 of it – the split flange’s underside, which is a 12 mm horizontal ledge all the way round. Flipped, that lands on the bed and everything else slopes inward.
- The cap has 41 225 mm2 – the whole cavity ceiling. Printed as modelled it would be one enormous unsupported span.
- The MK3S plate has 10 229 mm2, mostly the plate underside outside the
saddle’s footprint. Flipped, the plate is on the bed and the saddle legs point
up with the slot opening upward. It is the tallest thing in the list at 98 mm,
because the saddle also stands the mount off the frame – see
interfaces.md. - Segment 1 has none at all, and the hub 67 mm2. Both print as modelled.
- The outlet has about 1 000 mm2, a narrow annulus where the cone meets the neck. Small enough to bridge; watch it on the first one.
Settings
Section titled “Settings”Print in the material and layer height you intend to keep: the layer lines are the wall texture the funnel angle depends on.
Perimeters matter more than infill here. Everything structural in
loads.md is bending in a thin wall, so shell thickness is what
carries it; the bin wall governs at a safety factor of 4.8 and creep is the
thing that factor does not cover. Four perimeters is a better spend than more
infill.
Hardware
Section titled “Hardware”| Where | Fastener | Notes |
|---|---|---|
| hub -> plate | 4 x M4 x 20 + nuts | straight through both; the nut seats in the hub’s counterbore, which spotfaces the skirt’s cone flat |
| split joint | 6 x M4 x 20 + nuts | plus 2 x dia 4 dowels, which locate while the bolts clamp |
| split joint seal | closed-cell foam tape, ~2 mm x 10 mm | one face only, inside the bolt circle |
| MK3S clamp | 2 x M4 grub | pinch the frame; the saddle roof carries the weight |
| panel variant | 4 x M4 + washers | washers or a backing plate, not bare heads on sheet |
The split joint seal
Section titled “The split joint seal”Closed-cell foam tape – EPDM or neoprene, around 2 mm thick and 10 mm wide – run round one flange face inside the bolt circle. Deliberately a consumable rather than a groove and an O-ring: what leaks here is flake dust rather than liquid, printed flanges are never flat enough to seal metal-to-metal anyway, and foam takes up that error where a hard seal would need the flatness it cannot get. It also costs no geometry, so nothing has to be reprinted to change it.
Compress it with the bolts, not beyond about half its thickness. The dowels set the alignment, so the tape is not being asked to hold anything in place.
Assembly order
Section titled “Assembly order”- Bolt the hub down to the plate: bolts up from under the plate, nuts into the hub’s counterbores. There is 4 mm of flange under each seat.
- Mount the plate: MK3S clamp over the frame’s top edge and pinch, or bolt through the drilled panel. Panel hole is dia 65.
- Twist the outlet up into the hub’s lower socket.
- Screw the hose into the outlet – it threads, the reinforcing rib is the thread. Right-handed, 0.2 mm clearance, both settled on a coupon. A different hose needs its fits found by trial.
- Bolt the two body segments together, dowels first.
- Turn the body back by the sweep angle, drop it into the hub, and turn it forward to seat.
- Cap on last.
Steps 3 and 6 are 25 degree turns by hand. That is the point of the couplings: clearing a jam is twisting the outlet off, not undoing the assembly.
