Well Plate Pipette Guide
A parametric, 3D-printable pipette guide for laboratory well plates, written in OpenSCAD. It sits over a standard plate and steers the pipette tip into the centre of each well, through a tapered hole and a short cone that reaches into the well. That keeps the tip off the well wall and the sample, which matters for delicate work such as organoid culture.
By Cameron Brooks and Hadden Christ, 2026. The guide has been printed and used with 24- and 96-well plates.
pipette_guide.scad draws three parts around one plate definition:
- Stand: a frame that sits around the well plate, with arched cut-outs in all four sides.
- Guide: the plate the pipette goes through, which sits on the stand. Each well gets a tapered hole, wider at the top, inside a cone that enters the well. Under the guide, a lip with small snap bumps locates it in the stand. Lift tabs on the ends make it easy to take off, and row letters and column numbers are engraved in the top.
- Base (optional): a tray the stand nests in, with a hole under each well.
With guide_interstitial_protrusions = true (the default), the guide also has solid
cones, with no hole, between each group of four wells. They press on the plate to
hold it down.
Plates
Section titled “Plates”The plate definitions are in well_plates.scad. plate_selection picks one:
plate_selection |
Plate | Wells | Pitch | Well diameter | Default guide fits |
|---|---|---|---|---|---|
| 0 | 24 CytoView MEA | 4 x 6 | 18.00 mm | 15.00 mm | yes |
| 1 | 96 flat short | 8 x 12 | 9.00 mm | 6.86 mm | yes |
| 2 | 96 round medium | 8 x 12 | 9.00 mm | 6.86 mm | yes |
| 3 | 384 flat short | 16 x 24 | 4.50 mm | 3.63 mm | no |
| 4 | 1536 flat short | 32 x 48 | 2.25 mm | 1.50 mm (square) | no |
The default holes and cones are sized for the 24- and 96-well plates. On the 384- and 1536-well plates, the cones (5.97 mm across where they enter a well) are wider than the wells, and the render stops with a message naming the parameter to change. A guide for those plates needs smaller holes and cones, which nobody has designed or printed yet.
A plate definition is one array. The comment block in well_plates.scad lists each
field: rows, columns, pitch, the A1 offsets, well diameter, depth and shape, bottom
radius and flange heights. The grid and the outer dimensions follow the ANSI/SLAS
microplate standards, cited in references/. The well
dimensions come from the plate maker’s datasheet. To add a plate, add an array in
the same format to well_plates.scad and to the well_plates list, and add it to the
plate_selection options in pipette_guide.scad.
Parameters
Section titled “Parameters”The main ones, at the top of pipette_guide.scad, with their defaults:
| Parameter | Default | What it sets |
|---|---|---|
render_part |
"assembly" |
"assembly", "stand", "guide" or "base" |
render_well_plate |
true |
draws a transparent reference plate |
view_cross_section |
false |
cuts the view in half to show the holes |
plate_selection |
0 |
the plate, from the table above |
tip_diameter |
3.6 mm | the top of each guide hole |
bottom_hole_diameter |
2.6 mm | the bottom of each guide hole |
protrusion_extension |
3 mm | how far the cones reach into the wells |
protrusion_top_radius |
tip_diameter |
the cone’s outside radius at the guide |
protrusion_taper_angle |
5.5 deg | how much the cone narrows towards its tip |
guide_interstitial_protrusions |
true |
the solid cones between wells |
fit_clearance |
0.2 mm | clearance between the plate, stand and guide |
label_depth |
0.5 mm | how deep the labels are engraved |
To print, set render_part to one part at a time and turn render_well_plate off.
Tip checker
Section titled “Tip checker”tip_checker.scad is a small test plate for finding the hole size that suits your
tips before printing a whole guide. It has an 11 x 11 grid of tapered holes: the top
diameter steps from 6.0 to 8.0 mm across the columns, and the bottom diameter from
4.0 to 6.0 mm down the rows, both by 0.2 mm. Both are engraved on the plate. These are
the same quantities as the guide’s tip_diameter and bottom_hole_diameter, so the
numbers of the hole that fits go straight into the guide.
The checker’s range does not include the guide’s defaults (3.6 and 2.6 mm). To test
around other sizes, edit top_diameters and bottom_diameters at the top of the file.
Workflow
Section titled “Workflow”- Print the tip checker and try your pipette tips in it.
- Set
tip_diameterandbottom_hole_diameterto the hole that fits best. - Set
plate_selectionto your plate. - Render and export the stand, the guide and, if you want it, the base, one at a time.
- Print them, and try the guide on an empty plate before using it with samples. It should sit flat, and the tip should pass through without force.
Rendering
Section titled “Rendering”Render with the Manifold backend (openscad --backend=Manifold, or the Manifold
option in OpenSCAD’s preferences). Each part of the 24- and 96-well guides rendered in
2 s or less with OpenSCAD 2026.10.15.
| File | Contents |
|---|---|
pipette_guide.scad |
the stand, guide and base, and their parameters |
well_plates.scad |
the plate definitions |
well_plate.scad |
a model of a standard plate, drawn from a definition |
tip_checker.scad |
the hole-size test plate |
utils.scad |
cross_section(), used for the cross-section view |
references/ |
the ANSI/SLAS standards the plate geometry follows |
CHANGELOG.md |
changes by version |
Licence
Section titled “Licence”GNU Affero General Public License v3.0. See LICENSE.
