Syringe Actuator: Measuring a syringe
Each syringe gets its own frame, clip, crank and rod, from the numbers in
cad/purchased/syringes.scad; syringes in one body group share the body, lid and cap.
Syringe makers do not publish these: BD, for one, gives its syringe-pump dimensions only on request,
and ISO 7886-2 notes that diameters overlap between makers and that lengths and flange thicknesses
vary from mould to mould. A “3 mL syringe” is therefore not one shape; a 3 mL Norm-Ject is 10.8 mm
across the barrel where a 3 mL BD is about 10.1. The measured presets are the unbranded syringes
this was built and tested with; the BD 10, 30 and 50 mL are estimates. Measure the syringe you will
use, and enter it as its own preset, named for its volume and maker.
The numbers
Section titled “The numbers”All in millimetres. The barrel’s axis runs front (the nozzle) to back (the push-button).
| Key | What | Where | How much it matters |
|---|---|---|---|
stroke |
Usable plunger travel | Plunger from bottomed to its stop, as the change in exposed |
Most. Too long and the crank drives the stopper into its stop near the end of its swing, where a crank’s force is greatest |
exposed |
Plunger showing, stopper bottomed | Flange’s rear face to the push-button’s front face | Most, for the same reason at the other end |
button_d |
Push-button diameter | Across the push-button | High. The clip’s snap grips its edge by a fraction of a millimetre |
barrel_od |
Barrel’s outside diameter | Across the barrel, clear of the graduations | Medium. The barrel snaps into a ring |
button_t |
Push-button thickness | Through the push-button at its edge | Low. Sets a slot with clearance |
flange_t |
Flange thickness | Through a flange, clear of its ribs | Low. Sets a slot with clearance |
flange |
Flange [width, height] |
Across the flanges the long way, and across them the short way | Low. Sets the frame’s width and the window’s |
plunger_span |
The plunger’s widest | Across the plunger’s ribs (or its rod, if solid), in front of the push-button | Low. Sets slots with clearance |
barrel_l |
Barrel length | Flange’s front face to the shoulder at the nozzle’s root | Low. Checked against stroke, and drawn |
bore_d |
Barrel’s bore | Not measured: BD’s published bore for the volume | Only for the report’s torque estimate |
nozzle_l |
Nozzle length | The barrel’s shoulder to the syringe’s front end, the nozzle’s tip or its luer-lock collar’s face, whichever reaches further | Only for tip_x(), where a mounting adapter finds the tip; may stay undef |
Syringes are soft polypropylene, and metal caliper jaws squeeze them: a hard reading of a barrel comes out a tenth or so small. So:
- Lengths and widths: scan it. A flatbed scanner at 600 dpi is a calibrated, square-on camera
(0.04 mm a pixel) that touches nothing. Lay the syringe flat with a ruler beside it, and scan it
twice, plunger bottomed and plunger at its stop.
exposed,stroke,barrel_l,flange[0],button_d,barrel_odandplunger_spanall read from the two scans; measure from the scan’s pixels against the ruler, not by eye. - Thicknesses: calipers, lightly. Close the jaws until they just touch, and read without
squeezing.
flange_tandbutton_t. - Several units. Measure three of the same syringe if you have them, and enter the middle value.
- A photo from the side is a poor substitute: perspective makes near parts larger than far ones, so a phone photo is only good to a millimetre or so.
Adding one
Section titled “Adding one”Copy an entry in cad/purchased/syringes.scad, name it for the volume and maker
(syringe_3ml_terumo, say, picked as 3ml-terumo: the picked name takes a hyphen, not an
underscore, which tools/qa/qa.sh splits its job names on), and say in its comment how and when it
was measured. Add it to the syringes list at the bottom of that file, with the body group of the
syringes it should share a body with (a syringe bigger than the rest grows that body for the whole
group, and printed bodies then no longer fit), to the syringe choice in cad/main.scad, and to
SYRINGES in the justfile, then run just check and just test: layout() stops the build with a
message if the numbers cannot work (a barrel shorter than its stroke, say). Print the clip and check
the push-button snaps in, then the rest; if it is loose or will not go in, raise or lower grip in
the Customizer and print the clip again.
