Power Tools
These are the FAST group's own lab signs. They are written for one lab, its equipment, its layout and its local procedures, and are published so others can see and adapt them. They are not general safety guidance and they are not a substitute for training.
If you work somewhere else, follow your own workplace procedures and the requirements of your institution and jurisdiction.
reviewawaiting PI, post-doc, equipment owner or subject-matter review
Before You Start
Section titled “Before You Start”- Choose the right tool, bit, blade, disc, abrasive, speed, and setup for the material.
- Inspect the tool, guard, cord, battery, switch, chuck, bit, blade, or disc before use.
- Wear required eye, hearing, dust, face, and hand protection for the task.
- Wear long pants and closed-toe shoes.
- Tie back long hair and keep loose clothing, jewelry, and lanyards away from rotating or reciprocating tools.
- Clamp or secure the workpiece before cutting, drilling, grinding, or sanding.
- Check what is behind or under the work before cutting or drilling.
- Eye protection is required for all power-tool use.
- Hearing protection is recommended for angle grinders, circular saws, sanders, and any loud extended work.
- Use dust protection and ventilation for dusty work.
Tool Selection
Section titled “Tool Selection”| Tool | Use for | Ask first / avoid |
|---|---|---|
| Drill driver | Drilling holes and light screw driving | High-torque fastening, unknown materials, or work that cannot be clamped. |
| Impact driver | Driving screws, bolts, and fasteners that need high torque | Precision drilling, fragile parts, or fasteners/materials that may strip or crack. |
| Angle grinder | Cutting or grinding compatible materials with the correct guard and disc | Changing discs, cutting unknown materials, removing guards, or using damaged discs. |
| Circular saw | Straight cuts in compatible sheet or lumber-like materials | Unsupported stock, warped material, wrong blade, or work that can pinch and kick back. |
| Sander | Surface finishing with the correct abrasive and dust control | Unknown coatings, hazardous dust, wet material, or material that may melt or ignite. |
Gloves
Section titled “Gloves”Gloves are decided by whether one can be pulled in, not by which tool it is.
- NEVER wear gloves where a spinning bit, blade, disc, or chuck could catch them. That includes every stationary machine in TEB6.
- NEVER hold the workpiece in a gloved hand near a moving tool. Clamp it instead.
- Gloves are appropriate for the angle grinder when you hold the tool with both hands, to protect against sparks, abrasion, and hot or sharp material.
- For handheld circular saws, follow the manufacturer instructions and site-specific procedure rather than assuming gloves are required.
- Gloves may be used to handle blades, burrs, or sharp stock after the tool is stopped, unplugged or battery-isolated, and unable to restart.
Where To Work
Section titled “Where To Work”- TEB7 hand-held tools are for quick, light use only.
- Do dusty, noisy, extended, or disruptive work in the TEB6 stationary-tool area.
- Return TEB7 tools to their holders/cabinets when done.
While Using A Tool
Section titled “While Using A Tool”- Keep both hands, cords, clamps, and bystanders clear of the cutting or rotating path.
- Let the tool reach speed before contacting the work.
- Do not force the tool. Stop if it binds, grabs, overheats, vibrates, smokes, smells wrong, or sounds wrong.
- Keep guards in place and working.
- Wait for the tool to stop completely before setting it down.
- Keep dust, sparks, chips, and offcuts contained and away from people, chemicals, resin, and flammables.
When Done
Section titled “When Done”- Turn off and unplug the tool or remove the battery before changing bits, blades, discs, or abrasives.
- Put tools, batteries, chargers, bits, blades, discs, clamps, and PPE back where they belong.
- Clean dust, chips, scraps, and offcuts from the area.
- If you find a defective tool, stop using it, write a clear notice on the tool, and safely prevent operation if possible: remove the battery, unplug it, or physically block the control without damaging the tool.
- Contact the PI or a post-doc so the tool can be tagged out, repaired, or replaced.
Stop And Ask
Section titled “Stop And Ask”- Hand-held tools are on an honour system: if you are not familiar and experienced with the tool, get training first.
- Stationary tools in TEB6 require training and sign-off by the PI or a post-doc.
- Ask before cutting, grinding, sanding, or drilling unknown material.
- Do not cut, grind, sand, or drill materials that may produce hazardous dust or fumes, such as lead, asbestos, composites, or PVC, unless there is a formal containment/ventilation/PPE plan.
- Ask before making sparks, dust, fumes, or noise that could affect nearby people or work.
- Ask before working alone with a tool that can cause serious injury.
Related
Section titled “Related”- See Stationary Tools for drill press, miter saw, scroll saw, and other fixed tools in TEB6.
- See Manual Tools for flush cutters, pliers, screwdrivers, wrenches, knives, and small cutters.
Sources / Procedure Links
Section titled “Sources / Procedure Links”- CCOHS powered hand-tool guidance: https://www.ccohs.ca/oshanswers/safety_haz/power_tools/
- CCOHS electric power-tool guidance: https://www.ccohs.ca/oshanswers/safety_haz/power_tools/saf_elec.html
- CCOHS circular saw guidance: https://www.ccohs.ca/oshanswers/safety_haz/power_tools/saw_circ.html
- OSHA angle grinder safety talk: https://www.osha.gov/sites/default/files/2018-12/fy15_sh-27664-sh5_Toolbox_Angle_Grinder.pdf
- Western Engineering student shop safe operation procedures: https://www.eng.uwo.ca/departments-units/student-shop/health-safety.html
